BOB57 HD Cinematic LR & Freestyle 6″- Nebula Pro – GPS – Crossfire


Sold Out!

Pilot & videographer Ellisvan Jason and iFlight teamed up to craft a cinematic drone that ensures agility and flight time with some great features.


Sold Out!


Join the waitlist to be emailed when this product becomes available

The pilot & videographer Ellisvanjason and iFlight teamed up to craft a cinematic 6 inch drone that ensures agility and flight time and therefore combines the advantages of both 5 inch and 7 inch drones.


– 6 inch drone re-engineered: This drone was specifically designed for 6 inch

– H-shaped frame with robust middle section for less props in view while remaining stiffness

– XT60 front-mount: Compare to other drones the mount sits in the front and gives more space on the back.

– Built in BEC to directly power a GoPro (no battery needed)

– Hybrid motor design: This motor is optimised for 6 inch.  Can be used with bi- blades (efficiency) and tri-blades (agility & trust).

– Antenna mount: Solid antenna mount for less oscillations when using long antennas

– Long back bone: Enough space up to 3000mAh 6S batteries

– Gladiator shell: Protection shell from dust and water droplets (shall be removed for max. flight time)

– GPS: A high-end GPS is used to minimise the risk of failure during proximity flights

– ESC: The drone consists iFlight’s new ESCs with built-in spike absorber for more reliability

– 9min flight time with 1800mAh 6S

– 9+ with 3000mAh 6S Lipo or 4000mAh 6S Li-Ion

– Get Ellisvanjason’s tune on ellisvanjason.com


– Upper(middle) plate thickness: 2.5mm

– Bottom plate thickness: 1.5mm

– Total Dimensions: 254*254mm

– Bottom to top distance: 22mm

– Geometry: H-shaped frame

– Top plate thickness: 2mm

– Ellisvanjason 2506 motors

– Gemfan 6032 propellers

– Arm Thickness: 6mm

ELECTRONICS // BLITZ F7 Stack (F7 V1.1 + 55A 4in1 ESC)

FC //BLITZ F722 Flight Controller

  • Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter
  • Smartaudio / IRC Tramp VTX protocol supported
  • Firmware target: IFLIGHT_BLITZ_F722
  • Motor outputs: 4x (SH1.0 connector)
  • Flash: 32MB (Blackbox flash)
  • I2C serial: SDA / SLA pads
  • Dimensions: 36.5*35 mm
  • Barometer: DPS310
  • OSD Chip: AT7456E
  • LED controller: Yes
  • MCU: STM32 F722
  • Beeper pad: Yes
  • Gyro: BMI270
  • Weight: 7.8g
  • UARTS: 6

 Product Link

ESC // BLITZ E55 4-IN-1 2-6S 55A ESC

  • Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
  • Mounting Holes: 30.5*30.5mm/Φ4mm
  • Target:   IFLIGHT_BLITZ_G2
  • Supports 2-6S Lipo input
  • Current sensor: Yes
  • Constant: 55 Amps
  • Current rate: 200
  • Burst: 65 Amps
  • Weight: 15.3g
  • MCU: G071
  • BEC: No

 Product Link

BOB57 HD Included Components and Parts

  • 2 x GEMFAN 6032- CW propeller + 2 x  6032 CCW (Green)
  • 2 x GEMFAN 6032- CW propeller + 2 x  6032 CCW (Black)
  • 1 x Albatross LHCP 5.8GHz SMA FPV Antenna 150mm
  • 1 x Albatross LHCP 5.8GHz SMA FPV Antenna 60mm
  • 1 x USB Type-C 5V Balance Plug Power Cable 55mm
  • 2 x iFlight Lipo Strap 20*250mm (Black)
  • 1 x Nebula Pro Vista HD System
  • 1 x Pre-built and Tested BOB57
SKU: IFL-BOB57-TBS Categories: , Tags: ,